ABSTRACT
At present, the filtration of virus and other small particles in the air by meltblown cloth produced by electret treatment mainly depends on its electrostatic adsorption mechanism. However, because the surface charge of melt blown fabric can not be maintained for a long time, it can not maintain high efficiency filtration for a long time. Therefore, there is no guarantee for the medical staffs to not be infected by COVID-19. Therefore, it is necessary to improve the mechanical filtration efficiency of melt blown fabric in the situation of an electric charge loss. In this paper, nylon 6 (PA6) nanofibers were electrospun on melt blown cloth by electrospinning technology, and a sandwich material with melt blown cloth as surface layer and PA6 nanofibers as middle layer was made by hot- pressing technology;the surface morphology, thermal and mechanical properties of the sandwich material were characterized, and its filtration performance was tested. The experimental results show that the surface integrity of the sandwich material is high, and the diameter of nanofibers can reach about 67 nm;without the electret treatment, the filtration efficiency of the sandwich material for particles in an size of 0.2 μm is more than 95%,while the filtration efficiency of non-woven fabric is zero;the filtration resistance of the material is about 284 Pa, which is suitable for personal protection. © 2023 Chengdu University of Science and Technology. All rights reserved.
ABSTRACT
The global COVID-19 pandemic has triggered a huge demand for the protective nonwovens. However, the main raw material of nonwovens comes from petroleum, and the massive consumption of petroleum-based polymers brings great pressure to ecosystem. Therefore, it is significant to develop biodegradable protective barrier products. In this work, a polylactic-based composite (a tri-layer nonwovens composed of spunbond, meltblown and spunbond, SMS) was prepared and applied for protective apparel. The surface morphology and chemical changes of the fibers were characterized and analyzed by scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR) and energy dispersive spectroscopy (EDS). The liquid contact angle and permeability, breathability and moisture permeability, frictional charge and mechanical strength of the samples were evaluated and compared. The samples degradability was also recorded. The results demonstrate that the optimum formula for anti-fouling treatment on SMS is F-30. The treated fabric possesses superior liquid repellency and anti-permeability, with contact angles of water and alcohol at 128° and 115° respectively, while the alcohol repellent grade reaches level 7. The treated sample has less strength loss but exhibits favorable breathability, moisture permeability and anti-static properties, which can meet the requirements of protective apparels. After fluorine resin coating, the composite still provide excellent degradation performance, and the weight loss rate reaches more than 80% after 10 days water degradation. These results provide new insights for the application of PLA-based SMS in biodegradable protective apparel. © 2023 The Textile Institute.
ABSTRACT
A Cu film with the ability to rapidly inactivate the COVID-19 virus was easily fabricated at approximately 23°C on a Na-free glass substrate. The well-adhered Cu films with thickness of approximately 16 μm and surface area of 8.71 10-3 m2 g-1 were obtained by immersion of the glass substrate into an aqueous solution with dissolved Cu (II) complex of ammonia and ascorbic acid. The interface bonded between the film and glass substrate was very strong, such that the film did not peel off even when it was exposed to an ultrasonic wave of 100 mW (42 kHz) in water. The anti-COVID-19 activity in Dulbecco's modified Eagle's medium (DMEM) is effective within 2 h and is faster than that of commercial copper plates. The changes in the relative abundance of Cu2O and CuO crystallines on the Cu film due to DMEM treatment and those in surface morphology were examined by X-ray diffraction peak analysis and field emission-scanning electron microscopy, respectively. The flame atomic absorption analyses of the recovered solutions after DMEM treatment indicated that the Cu ions from the Cu film with DMEM treatment for 1 hour at a concentration of 0.64 ± 0.03 ppm were eluted 2.3 times faster than those from the Cu plate. The rapid elution of Cu ions from Cu2O crystallines on the film in the early stage is the primary factor in the inactivation of the COVID-19 virus, as elucidated from the time dependence of eluted Cu ions by DMEM treatment. Results from thermogravimetric and differential thermal analysis (TG-DTA) of the powder scratched from the Cu film suggested that a trace amount of organic residues remaining in the Cu film was important in the rapid activity. © 2022 World Scientific Publishing Company.
ABSTRACT
(1) Background: A quest for a highly sensitive and reliable humidity monitoring system for a diverse variety of applications is quite vital. Specifically, the ever-increasing demand of humidity sensors in applications ranging from agriculture to healthcare equipment (to cater the current demand of COVID-19 ventilation systems), calls for a selection of suitable humidity sensing material. (2) Methods: In the present study, the TPPNi macromolecule has been synthesized by using a microwave-assisted synthesis process. The layer structure of the fabricated humidity sensor (Al/TPPNi/Al) consists of pair of planar 120 nm thin aluminum (Al) electrodes (deposited by thermal evaporation) and ~160 nm facile spin-coated solution-processable organic TPPNi as an active layer between the ~40 µm electrode gap. (3) Results: Electrical properties (capacitance and impedance) of sensors were found to be substantially sensitive not only on relative humidity but also on the frequency of the input bias signal. The proposed sensor exhibits multimode (capacitive and conductometric) operation with significantly higher sensitivity ~146.17 pF/%RH at 500 Hz and 48.23 kΩ/%RH at 1 kHz. (4) Conclusions: The developed Al/TPPNi/Al surface type humidity sensor's much-improved detecting properties along with reasonable dynamic range and response time suggest that it could be effective for continuous humidity monitoring in multi environmental applications.